metallurgy natural gas steam atmospheric pressure water tube boiler
HOT
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
HOT
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
HOT
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
Reason #8: Boiler pressure is too low or too high when heating or hot water is on. Normally, when the heating is on, the boiler pressure is around 1.5-2 bar and around 1-1.5 when it's off. Monitor the water pressure meter on the front of the boiler for any changes.Get Price
123. Why large boilers are water tube type ? Water tube boilers raise steam fast because of large heat transfer area and positive water circulation. Thus they respond faster to fluctuations in demand. Further single tube failure does not lead to catastrophy. 124. What type of boiler does not need a steam drum ? Super-critical pressure boiler. 125.Get Price
A safety valve is a valve that acts as a fail-safe.An example of safety valve is a pressure relief valve (PRV), which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits. Pilot-operated relief valves are a specialized type of pressure safety valve. A leak tight, lower cost, single emergency use option …Get Price
Steam blanketing is a condition that occurs when a steam layer forms between the boiler water and the tube wall. Under this condition, insufficient water reaches the tube surface for efficient heat transfer. The water that does reach the overheated boiler wall is rapidly vaporized, leaving behind a concentrated caustic solution, which is corrosive.Get Price
A steam locomotive is a rail vehicle that provides the force to move itself and other vehicles by means of the expansion of steam.: 80 It is fuelled by burning combustible material (usually coal, oil or – now rare – wood) to heat water in the locomotive's boiler to the point when it becomes gaseous and its volume increases 1,700 times. . Functionally, it is a steam engiGet Price
Steam blanketing is a condition that occurs when a steam layer forms between the boiler water and the tube wall. Under this condition, insufficient water reaches the tube surface for efficient heat transfer. The water that does reach the overheated boiler wall is rapidly vaporized, leaving behind a concentrated caustic solution, which is corrosive.Get Price
Heath exchanger tubes in the first effect are heated by steam from a boiler or a turbine. Cold seawater is either sprayed or distributed over the surface of the evaporator tube in a thin film to promote rapid boiling and evaporation. Steam flowing into the tubes condensed (inside the tubes) into pure water.Get Price
Water absorbs more heat for a given temperature rise than any other common inorganic substance. It expands 1600 times as it evaporates to form steam at atmospheric pressure. The steam is capable of carrying large quantities of heat. These unique properties of water make it an ideal raw material for heating and power generating processes.Get Price
A safety valve is a valve that acts as a fail-safe.An example of safety valve is a pressure relief valve (PRV), which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits. Pilot-operated relief valves are a specialized type of pressure safety valve. A leak tight, lower cost, single emergency use option …Get Price
Creep failure is an important phenomenon for steam and chemical plants which operate at high temperatures of 450 to 550°C, boilers, ovens, gas turbines, supersonic jets, rockets, missiles, and nuclear plants all working at very high temperatures. Creep failures or ruptures are easy to identify due to the deformation (necking) that occurs.Get Price
Heath exchanger tubes in the first effect are heated by steam from a boiler or a turbine. Cold seawater is either sprayed or distributed over the surface of the evaporator tube in a thin film to promote rapid boiling and evaporation. Steam flowing into the tubes condensed (inside the tubes) into pure water.Get Price
123. Why large boilers are water tube type ? Water tube boilers raise steam fast because of large heat transfer area and positive water circulation. Thus they respond faster to fluctuations in demand. Further single tube failure does not lead to catastrophy. 124. What type of boiler does not need a steam drum ? Super-critical pressure boiler. 125.Get Price
b. Diesel fuel systems, gas oil systems, and kerosene systems. c. Acid lines, cryogenic systems, and air drier systems. d. Reboiler oil systems, boiler piping, and steam turbine lines. 83. What should be considered when testing carbon steel piping during cold weather or if cold fluids are used in the testing? a.Get Price
Creep failure is an important phenomenon for steam and chemical plants which operate at high temperatures of 450 to 550°C, boilers, ovens, gas turbines, supersonic jets, rockets, missiles, and nuclear plants all working at very high temperatures. Creep failures or ruptures are easy to identify due to the deformation (necking) that occurs.Get Price
Water absorbs more heat for a given temperature rise than any other common inorganic substance. It expands 1600 times as it evaporates to form steam at atmospheric pressure. The steam is capable of carrying large quantities of heat. These unique properties of water make it an ideal raw material for heating and power generating processes.Get Price
When a diaphragm devise is used for boiler water level measurement, the boiler pressure is compensated for or off-set by: using a bellows on the HP side. a spring which balances the differential pressure. applying the pressure to both sides of the diaphragm. reversing the reference and variable legs.Get Price
steam boiler for building heating including all piping and radiators. 1.6 A water tank used in a residential area initially contains 120 L of water (ρw=1000kg/m3). The tank 1.3 Three cubic meters of air at 25°C, and 1bar have a outlet valve opens for watering the lawn at …Get Price
b. Diesel fuel systems, gas oil systems, and kerosene systems. c. Acid lines, cryogenic systems, and air drier systems. d. Reboiler oil systems, boiler piping, and steam turbine lines. 83. What should be considered when testing carbon steel piping during cold weather or if cold fluids are used in the testing? a.Get Price
Feel free to reach out if you want to collaborate with us, or simply have a chat.
